+86-0574-88106851 sales@relong.cn
Relong Auto-parts Co.,ltd
Relong Auto-parts Banner

Design Programming of Die Casting Parts

2018.09.11
Design specification for wall thickness of auto die casting parts

Die casting parts with thin walls have higher strength and better compactness than the ones with thick walls. In view of this, the design of die casting parts should follow this principle: the thickness of the wall should be reduced as much as possible and be kept uniform on the premise of sufficient strength and rigidity of the castings. Practice has proved that the wall thickness of die casting parts china generally should be 2.5 to 4mm, and parts with the wall thickness exceeding 6mm are not suitable for die casting process. The influences of too thick and thin wall on the quality of the castings: If the wall of the castings is too thin, the metal welding will be affected, thus directly affecting the strength of the castings and causing difficulties in molding. When the wall is too thick or uneven seriously, the shrinkage and crack are easily produced. Besides, with the increase of the wall thickness, the number of defects such as shrinkage and porosity will also increase, which will also reduce the casting strength and affect the casting quality.


auto die casting parts


Design specification for machining allowance of pressure die casting parts
In general, due to the limitations of the die casting process, sometimes the size accuracy, surface roughness, or geometric tolerance of the die casting cannot meet the requirements of the product drawings. In such a situation, the enterprise should first consider the use of fine finishing processes such as correction, light pulling, extrusion, and plastic finishing to repair, and if the finishing process cannot completely solve these problems, we should machine some parts of the castings. It is worth noting that the smaller machining allowance should be taken into consideration in the process of mechanical processing, and the surface which is not affected by the parting surface and motion molding should be considered as the blank base surface, so as not to avoid the processing precision.

Design specification for inclination of auto die casting parts
When designing die castings, the structural inclination should be considered. When there is no structural inclination, the technical inclination of demoulding should be kept at the places need. Besides, the direction of the slope must be consistent with the direction of the casting demoulding .
Related News
  • What Caused Poor Vulcanization Of Silicone Rubber Products?

    What Caused Poor Vulcanization Of Silicone Rubber Products?

    April 13, 2018We often meet poor vulcanization in the production of silicone rubber products, also called "unfamiliar" vulcanization. The result is seriously bad if the customer gets such products. What are the fac...view
  • Automotive Rubber Damping Components

    Automotive Rubber Damping Components

    September 3, 2018Along with the rapid development of high-performance technology in the automotive manufacturing industry, the development of automotive technology seeks to be economical in the use of automobiles, and...view
  • The Impact Factors: Why Does The Surface Of Rubber Products Whiten

    The Impact Factors: Why Does The Surface Of Rubber Products Whiten

    April 13, 2018I believe many people have met this problem: the surface of rubber products gets whiten after a period of use. Do you particularly feel troublesome about this problem? Today I'll give you the reasons ...view
  • A Brief Introduction of Rubber Seals

    A Brief Introduction of Rubber Seals

    June 22, 2018Rubber seals are generally used to prevent fluid media from leaking from machinery or instruments, and can also be used to prevent dust, sand, and air from entering the sealing mechanism. The conditio...view
  • The Structure And Function Of Rubber Sealing Grommets

    The Structure And Function Of Rubber Sealing Grommets

    June 26, 2018What is a rubber grommet? What is a rubber sealing grommet? The grommet is used in a variety of specifications, and the shape affects the sealing effect, which is used to reduce friction, prevent leak...view
  • Classification of Rubber Parts

    Classification of Rubber Parts

    August 6, 2018From the whole vehicle, in addition to tires and internal and external decorative rubber parts, rubber parts are required to be classified into three categories according to their types.1. HoseFor eng...view
  • TEL:+86-0574-88106851
  • FAX:+86-0574-88106851
  • EMAIL:sales@relong.cn
  • ADDRESS:11/F, South Building, No. 1299, East Yinxian Avenue, Ningbo, China